Mat Irvine update:
After my initial report on Fujimi’s surprise release of the 1:24 scale Spinner Police Car from the classic science-fiction movie Blade Runner, here’s how I worked to complete the model.
Hard to find details
Frankly, one major problem was finding enough references, to check details when building the model. The obvious starting point might be the movie itself, but a glance at Blade Runner makes you realise that the future-view of Ridley Scott (and of author Philip K. Dick, for that matter) is pretty dank and dismal. Most Spinner shots show a cityscape shrouded in smog and rain, so trying to ascertain details direct from the movie is not worth the bother - frankly, forget it! There is however logical reasoning in that if this is how Spinners appear on-screen, it’s how they should be depicted, but even here one has to start somewhere.
Magazines to the rescue
Given the popularity of Blade Runner, I would have thought that details would be everywhere, from publications of the time and online, but it isn’t so. Fortunately, two revered publications from 1982 - Cinefantastique and Cinefex - did show such details. Cinefantastique’s double-issue, Vol 12, Numbers 5 and 6, and Issue 9 of Cinefex contained features that helped with my build considerably.
Shot in Los Angeles
Even so, there are areas of debate, even down to the main exterior colour. Yes, it’s ‘blue’ but what shade, exactly? The few colour photos that exist of the full-size car, (there were a number of miniatures) tend to show it as a fairly light blue, but the movie shots indicate it was darker, in fact more how you’d expect a police car to look! In fact, the differences in shade are almost certainly down to where the movie was made, not at a UK film studio, where many sci-fi movies of the time were shot, but in Los Angeles, where the sunshine is - most of the time - pretty bright, which was almost certainly the reason for the washed-out blue, when the car was photographed outside. Consequently, I chose Testors Dark Blue enamel, though other model paint companies have similar shades.
Two sci-fi movies
You can choose between ground or flight modes for this 1:24 scale Fujimi Spinner, though as the differences are purely down to the front wheel and cover positions, it’s possible to let the model be convertible, one to the other. Fujimi does not supply a display stand with the Spinner kit, which is a pity if you want it in flight mode - the Aoshima DeLorean from Back To The Future II (BttFII) rightly comes with one. Incidentally, there is a connection between these two movies - in the Town Square shots of BttFII, you can spot a Spinner and a number of other futuristic movie cars that were used to fill parking slots!
Ground to flight mode
The two items that move when a Spinner translates from ground to flight mode are the front wheels, which fit higher up, and the covers, which swing through 90 degrees. The Spinner’s underside is finished in the same blue. Note the ventral viewports for the police aboard to see the ground below their feet, and the onboard lights for illumination at night.
Gene Winfield’s Spinner
Cinefantastique page featuring an actual 1:1 scale Spinner, built by car customizer Gene Winfield. Note the photo at the bottom shows the washed-out light blue, and how clean the vehicle is - the exterior detailing, decals, and dirt, had yet to be added!
Mr J note:
The website Starship Modeler has a detailed look at this Fujimi kit, together with some brickbats and bouquets, so you might wish to go over and have a look. Mind you, good or bad, this is the only injection-moulded plastic kit to this scale...
Spinner and Blade Runner stuff here.
Starship Modeler here.
Cinefantastique here.
Good article. Nice build!
ReplyDeleteJust to clarify, the paint colors specified in the intructions are for Mr. Color lacquers. The second column in the paint chart lists Mr. Color paint numbers.
Some details in this kit don't match what was in the movie, such as the style of the headrests, the extra flashing light on the roof, the fluorescent tubes on the front of the car (2 instead of 1). These details match the restored Spinner which is on display in the Science Fiction Museum in Seattle. One exception is the exterior color. It was blue in the movie, but the restored Spinner is metallic blue.
An article about the restoration of the flying Spinner can be found here: http://media.bladezone.com/contents/film/production/props/spinner3/spinner_rising.php
The style of rc car itself has
ReplyDeletechanged all over the community. Many nations like Italy, Malaysia,America,Japan etc. have
rolled over their editions of assault choppers. They modified the main
drawbacks of rc car or Helicopter. But it can be absolutely highlighted that the rc car or chopper is the
pioneer in the assault chopper household. In this workshop I’ve tried to put forward
some of the style functions of the same.Blade Helicopters
Thanks for this..appreciate the clear lighting and sharpness of the pics, but you should have made an atmospheric shot with it also, as the hard lighting is a little cruel on the surface, and it makes me wonder if people are still using paste wax on models, which used to be talked about even the in sixties magazines. I think I'll get one of these and do a worn surface...metal showing...some rust....it might help in the realism. Tight little kit, tho.
ReplyDeleteThe Spinner is certainly suited for a gritty diorama - and also as background for other sci-fi scenarios.
ReplyDeletePerhaps starring as a spaceport security vehicle, or (in red) as an emergency control car in charge of a starship crash scene. Or how about being crunched by a runaway ED209 robot?!